Montigo C2120 Owner's Manual download pdf (Page 7)

CVIEW-PRC Custom Gas Fireplace

Part No. XG0704

f i r e f e a t u r e

Installation

Note: After gas line is connected, each appliance connection,

valve and valve train must be checked while under normal

operating pressure with either a liquid solution, or leak

detection device, to locate any source of leak. Tighten

any areas where bubbling appears or leak is detected until

bubbling stops completely or leak is no longer detected.

DO NOT use a ﬂame of any kind to test for leaks.

Installing The Gas Line

The gas connection is located on the right side of the lower portion of

the ﬁreplace body. The manufacturer requires a service shut oﬀ valve

located in an accessible location to isolate the gas supply. The gas

line must be installed, and tested for leaks before ﬁnishing the CVIEW

Fireplace. Natural Gas requires a minimum inlet gas supply pressure

of 5.5" W.C. & a manifold pressure of 3.5" W.C. Propane requires a

minimum inlet gas supply pressure of 11" W.C. & a manifold pressure

of 10" W.C. The manifold outlet pressure is set from the factory to the

appropriate pressure and should be veriﬁed. The manufacturer has

provided an inlet pressure tap location in the ﬁreplace for easy access.

The control valves have a provision to remove a 1/8 plug so that a

hose barb ﬁtting can be installed to check pressure.

Figure 6. Gas line access.

Refer to chart on page 3 for correct dimensions.

Figure 5. Combustible surrounds.

LP or NG Hookup

1/2”NPT

Electrical Connection

to Service Panel

Installation Of Electrical Supply

The C-View Fireplace is supplied with an external electrical Control

Panel pre-wired by the factory. The standard gas control cable is 15

feet between the ﬁreplace and the external panel, additional length

is available upon request. The external panel is 16" x 16" x 6" and

must be located in an accessible location. The C-View requires 120V

electrical supply on a dedicated 15 amp fuse or circuit breaker to

the Control Panel

6”

MIN

Page 7

Installing The Remote Switch

The CVIEW-PRC's two gas valves, located inside the unit and under-

neath the burner, may be connected to a wall switch or a hand-held

remote. The valve operates on a 24V circuit. DO NOT connect the

gas valve to an external circuit. The external electrical panel supplied

with the ﬁreplace is equipped with a 20 foot low voltage wire, for con-

necting to a wall switch of your choice, longer lengths are an option.

The electrical panel has three connection boxes on the side of the

panel marked: 110 Volt Power Supply, Power Vent Motor, and Gas

Control Wiring.

First Connect the White, Black, and Green (Ground) wire coming

from the power vent motor in the box marked Power Vent Motor. Then

connect the cable from the ﬁreplace. Last connect the power supply to

the box marked 110 Volt Power Supply. See the diagram on page 9

for the cable installation.

Figure 7. Electrical Supply

CAUTION:

 Do not obstruct, or attempt to conceal, the vent termination.

These actions will aﬀect the operation of the ﬁreplace, and may

be hazardous.

 In heavy snow areas, take extra care to prevent snow buildup

from obstructing the vent termination.

Installations in Canada must be electrically grounded in accordance

with CSA C22.1 Canadian Electrical Code Part 1 and/or Local Codes.

Installations in the USA must be electrically grounded in accordance

with local codes or, in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70-1987.

10V Power Supply

Power Vent Motor

Gas Control Wiring

Wall Switch

Air Proving Switch

Fuse

Fan Speed

Control

Post Purge

Control

1 2 3 4 5 6 7 8 9 10 11 12 ... 19 20

Comments to this Manuals

No comments

Montigo C2120 Owner's Manual Page 7

Comments to this Manuals

Related products and manuals for Fireplaces Montigo C2120