Montigo R720 Instruction Manual

Canadian Heating Products Inc. Langley, BC V4W 4A1 | Montigo Del Ray Corp. Ferndale, WA 98248®C USRead and understand this manual. Improper ins

Place the Fireplace on the platform and install the Vent pipe, and Power Vent module� Next, connect the Gas line, and provide a gas service shut-off v

Figure 5. Completed back frame Fireplace installationBack framing the Fireplace NOTE: Maintain a 1" clearance around the throat (projection at t

Picture of Non combustible HeaderRecessed Installation: This replace can be recessed into the oor to get the viewing area as low as possible.Mainta

Figure 7. Flue cover and collar removal, Top Vented replaceFigure 7a. Flue cover and collar installation, Rear Vented replaceR720 & R820 Powe

Figure 8. Factory installed Top Vent Pressure Sensing TubeFigure 8a. Supplied Rear Vent Pressure Sensing TubeFigure 9. Removal of Top Vent air baf

Figure 10. Straight Vertical, Top or Rear Vent, Roof mounted power vent. Figure 10a. Multi-Elbow, Top or Rear Vent, Roof mounted powe

Figure 10b. Multi-Elbow with downward vent run, Top or Rear Vent, Roof mounted power vent. R720 & R820 Power Vent Indoor Gas Fir

Figure 12. Straight Horizontal, Top or Rear Vent, Wall mounted ... power vent. Figure 12a. Multi-Elbow, Top or Rear Vent, Wall mou

D** Figure 12b. Multi-Elbow with downward vent run, Top or Rear Vent, Wall mounted power vent. Section 3-3-1: Installing Wall Moun

The following components and associated Montigo part numbers are for installation of a roof or wall mounted Power Vent. Only use Montigo Vent Componen

Page 2XG0772 - 100614Table of ContentsR720 & R820 Power Vent Indoor Gas FireplaceInstruction Manual ContentsSafety Alerts � � � � � � � � � � � �

Section 3-5: Heat Shields Installing a Wall Mounted RHS102 Heat shieldThe RHS102 Heat shield must be used if vent pipe passes through a wall or ceili

R720 & R820 Power Vent Indoor Gas FireplacePage 21XG0772 - 100614InstallationSection 4: WiringFigure 15. R720* / R820* Series Control Box / Powe

Figure 15a. (Control Panel Overview)Figure 15b. R720* / R820* Control ModuleLeft-side View Right-side ViewFigure 15c. (Remote Switch Wire connection)

115R1 R2 R3R1R2LightPVPlugPV Speed ControllerYellowYellowBlackBlueBlueBrownYellowBlueBlackWhiteWhite1234 5Combustion AirFlueGasWallSwitchOrangeWhiteBl

Figure 17. Gas Inlet Supply location.Fuel TypeVerify that your replace is compatible with your available gas type. Natural Gas or Propane shown by &q

Figure 18. LED Indicators If the red LED is illuminated (beside the fuse) you have power to the panel� If no LED, check fuse and replace with equall

As shown in Figure 19; Install the supplied Non-combustible cement board to overlap the new Horizontal & Vertical 2 x 4's, See Figure 5� Plac

Figure 20� Combustible mantles and facings. (Not to scale)Finishing Around the FireplaceNon-combustible mantels and mouldings may be safely installed

Step 3: Remove the trim from the bottom of the door as shown.Step 4: Remove the other side, as shown in Steps 1 - 3.Removing the door trim:Follow

The R720* / R820* is supplied with glass restones. To install the restones remove the trim and door as shown in the previous section. Follow these i

Congratulations on your purchase of a Montigo Fireplace� With over 30 years of experience, Montigo is committed to providing you with a gas replace

STARTUP SEQUENCE:1) Turn the wall switch ON2) The combustion air switch relay will light up and the blowers will start. Within 10 seconds the

General Have the replace and installation inspected yearly� The inspection must include, but is not limited to, the following: • A visual che

R720 & R820 Power Vent Indoor Gas FireplacePage 32XG0772 - 100614AppendixAppendix A: Power Vent LocationsFor installation instructions on this te

R720 & R820 Power Vent Indoor Gas FireplacePage 33XG0772 - 100614AppendixPVVEX510-300 Power Vent LocationsvvFIXEDCLOSEDOPERABLEFCBvvOPERABLEFIXED

PVHEX510-300 Horizontal Power Vent DetailR720 & R820 Power Vent Indoor Gas FireplacePage 34XG0772 - 100614AppendixFor installation instructions o

R720 & R820 Power Vent Indoor Gas FireplacePage 35XG0772 - 100614AppendixPVHEX510-300 Power Vent LocationsvvFIXEDCLOSEDOPERABLEFCBvvOPERABLEFIXED

R720 & R820 Power Vent Indoor Gas FireplacePage 36XG0772 - 100614AppendixPVHFL510-300 Horizontal Power Vent DetailFront ViewEaves / Overhang Wal

R720 & R820 Power Vent Indoor Gas FireplacePage 37XG0772 - 100614AppendixPVHFL510-300 Power Vent LocationsvvFIXEDCLOSEDOPERABLEFCBvvOPERABLEFIXED

The WarrantyThe Companies warrants the Montigo Gas Appliance to be free from defects in materials and workmanship at the time of manufacture. On the M

Amendment (Gas Fireplace / Equipment sold in the State of Massachusetts) 5.08: Modications to NFPA-54, Chapter 10 (1) Revise NFPA-54 section 10.5.4.

Installation and repairs should be done by an authorized gas fireplace service technician. The appliance should be inspected before use and at least a

XG0772 -100614R720 - R820Single Sided Gas Fireplace

Introduction to the R-Series Fireplace: The complete system will require a rebox, a power vent module, an electrical control panel, and a vent system

Section 1: Product DimensionsFront ViewFigure 1� R720* Fireplace dimensions (Tolerance ± ⅛").Top ViewSide ViewGas InletCombustion Air Switch Sen

Figure 1a� R820* Fireplace dimensions (Tolerance ± ⅛").Front ViewSide ViewTop View 40 1/16" 18" 108 11/16" 97 1/8"

Frame in the enclosure for the unit with framing materials, see Figure 3.NOTE: When constructing the framed opening, please ensure there is access to

Figure 3. Fireplace installation, (Rough Frame-In dimensions). Framing DimensionsModel Q R UR-Series R720* 101" 46"**23"†R-Series R820