Montigo P42DF User Manual

®C USRead and understand this manual. Improper installation, adjustment, alteration, service or maintenance can cause serious injury, property damage

Figure 9. Top vent, Roof mounted termination with no offset in vent run.Figure 9a. Top vent, Roof mounted with 1 offset (1 offset= two 90° bends).Fig

Figure 9c. Rear vent, Roof mounted venting (1 = 90° bend).Support ringSupport plate32’ max Termination 12” Max.PVTK1 PEXT SectionsNote: Images are

112”2”12”12”Section 3-3: Installing a Wall Mounted Direct Vent Termination This section applies to installations where the direct vent termination wi

The Venting Graph: P42DF*Measure the vertical height from the replace hearth to the centre of the termination and the horizontal run from the replac

Figure 14. Rear Vent Venting Graph for NG and LP wall mounted terminations.Figure 14b. Rear Vented, wall mounted Multi-elbow termination ins

Figure 15. Corner (Rigid) installation. (NG Models Only)Figure 15a. Corner (Flex) installation. (NG Models Only)45° Corner Installation.Attach an PEL-

A - Termination PTO4 (3" Length)PTO4F (3" Length)PVTK1SSB - Frame Kits MSR (Stucco Frame)MOSR (Stucco Frame)BSR-4

Section 3-3-3: Heat ShieldsInstalling a Wall Mounted RHS8 Heat shieldThe RHS8 Heat shield CANNOT be used when the Termination is WITHIN (36" Min.

78" 218" 6 5/8 512" Section 4: Wiring ModelsP42DFN-FP42DFL-FFigure 18. Wiring diagram for P42DF with SIT Proame Electronic Ignitio

Figure 20. Gas line access.When pressure testing the fireplace, Gas line, and input system follow the appropriate local codes or your area. DO NOT co

Instruction Manual ContentsSafety Alerts 3Introduction 3Section A: Before You Start 4Installation Checklist 4Rating Plate Sample 5Section 1: Ins

Figure 21. Combustible mantels and facings. WARNING!When covering the upper metal portion of the replace, up to 4" (as shown, Fig.21) with a

Section 6: Screen Installation and RemovalScreen BottomTabsScreen TabReceptaclesUpper ScreenStudsUpper ScreenStud CatchLeft Side Detail Left Side Deta

Removing the door:The P42DF* doors are removed in a few simple steps. Follow these instructions below to remove the Horizontal access panel, unlatch t

Section 8: Installing the Accessories Installing the FirestonesThe P42DF* is supplied with restones. Remove the Door as shown in the previous Instruc

Installing Optional Speckled Stones [RR300SS]Once the glass door has been removed as shown in the previous section, place the speckled stones evenly a

Installing the Driftwood Log SetStep 1. Remove the glass door as described in the previous section. LGS581 23456Step 3. Unpack the logs and handle wit

PilotStep 8. Place log 2 from LGS59 in front of pilot. Place log 3 from LGS59 on top of log 2. 5423PilotStep 9. Place log 4 from LGS59 in front of por

To Turn Off Gas To Appliance:1. Turn off replace using wall switch or remote control.2. Remove the lower Horizontal access panel.3. Turn the incom

GeneralHave the replace and installation inspected yearly. The inspection must include, but is not limited to, the following:  A visual check of t

Troubleshooting: SIT Proame 2:The following is a troubleshooting chart of possible problems:If your replace still does not operate correctly, c

MODELNatural GasLiquid PropaneGas Rating(BTU hr)Linear Burner w/ Glass media AccessoriesSIT Electronic IgnitionP42DFN-FX 32,000 X XP42DFL-FX 32,000 X

Replacement Parts List - Proame 1P42DF*NG Gas Valve with Stepper Motor RGC3033LP Gas Valve with Stepper Motor RGC3034NG Pilot Assembly RPA035LP Pilot

Appendix A: Venting TerminationsLocation Canada* USA**A clearance to the termination frame above grade, veranda, porch, deck, or balcony 12 inches 12

The WarrantyThe Companies warrants the Montigo Gas Appliance to be free from defects in materials and workmanship at the time of manufacture. On the M

Amendment (Gas Fireplace / Equipment sold in the State of Massachusetts) 5.08: Modications to NFPA-54, Chapter 10 (1) Revise NFPA-54 section 10.5.4.

XG0195 - 150204.2P42DF Single Sided Gas Fireplace

IMPORTANT MESSAGE: SAVE THESE INSTRUCTIONSThe P42DF* Direct Vent replace must be installed in accordance with these Instructions. Carefully read all

Rating Plate SampleFigure A: Rating Plate for IPI eletronic ignition 

Figure 1. Fireplace dimensions (Tolerance ± ⅛").Please review the Pre-Installation Checklist on Page 4 for general information on preparing for

Frame in the enclosure for the unit with framing materials. The framed opening for the assembled replace is 42" wide, x 42" high x 21 7/8&q

Clearances When installing a shelf over the top of the replaces, the following guidelines must be adhered to: For Rear Vent applications,

Figure 8. Flue cover and collar removal, Top Vented replace.Figure 8a. Flue cover and collar installation, Rear Vented replace.Section 3-1: Convert